Tonewheel General Hospital
LOGIN | View Shopping Gurney - VIEW GURNEY | CHECKOUT
Fast, Friendly, Amusing!
Fast, Friendly, Efficient!
Fast, Friendly, Obsessed!
Fast, Friendly, Psychic!
Fast, Friendly, Insightful!
Fast, Friendly, Conscientious!
Fast, Friendly, Knowledgeable!
Fast, Friendly, Accomodating!
Fast, Friendly, Kindhearted!
Fast, Friendly, Good-Natured!
Fast, Friendly, Reliable!
Fast, Friendly, Thoughtful!
Fast, Friendly, Amenable!
Fast, Friendly, Philosophical!
Fast, Friendly, Scintillating!
Fast, Friendly, Inspiring!
Fast, Friendly, Eccentric!
Fast, Friendly, Un-infected!
Find in the

Subscribe to Our
Email Newsletter.

Email address:
Hammond Organ Parts : Accessories

Number of Items found: 10

TWG Generator Isolation Bushings (B-3, C-3, A-100 organs)
Hammond organ tone generators were designed to float on a set of springs above the generator shelf. This kept motor and gear noise from resonating through the wooden console case. The generator needs to be secured when the organ is moved to prevent it from swinging around. When it swings the generator studs strike the generator shelf below, turning it into sawdust. This makes ovals out of the previously round generator mounting holes, and tears wires off the generator terminal strip.
This isolation kit permanently secures the generator without transmitting noise to the cabinet. The radial support ribs on the mount are out of phase on each side to further aid vibration isolation.

Installation is performed most easily by raising the manuals, removing the generator springs and lifting the generator to slide a bushing onto each stud. The bushing end rests in the mounting hole, while a second bushing is inserted on the underside of the generator shelf and held in place with the washers provided and the existing bolt. Bolts are also available (see part number GENSCRW).
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
ISOMOUNTTWG Generator Isolation Bushings (B-3, C-3, A-100 organs)Stocked0.2$25.00$25.00

Bristol (Spline) Wrench
Bristol key (also known as a spline wrench) used for removal of the motor pulleys from single motor models and the vibrato scanner rotor.
Spline wrenches, while similar in appearance to Allen wrenches, differ in that the fastening end resembles a 4- or 6-toothed gear which mates with a similar hole in the set screw. The design applies almost all of the turning force at right angles to the fastener axis, greatly reducing the possibility of stripping the head of the fastener when tightening. They are frequently used to secure knobs on front panel controls or gears on shafts, where extreme tightening is required.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
SPLINEBristol (Spline) WrenchStocked0.2$7.00$7.00

H-Series Vibrato Scanner Drive Belts
Replaces missing, stretched, cracked or broken drive belts in H series organs with the under-the-shelf vibrato unit. These belts slip over the motor pulley and the pulleys on the vibrato and celeste scanners. Please note: these belts are only applicable to the version of the H-100/200/300 series organs with the retro-fit motor and scanner units mounted below the tone generator shelf. If your scanner is driven from a shaft located on the generator motor the part number for that belt is HBELT-SQ.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
HBELTSH-Series Vibrato Scanner Drive BeltsStocked0.2$4.00$4.00

H-Series Vibrato Scanner Drive Belt - Square Scanner
Replaces missing, stretched, cracked or broken drive belt in H series organs with square vibrato scanner. This belt slips over the motor pulley and the pulley on the vibrato scanner. Please note: these belts are only applicable to the version of the H-100/200/300 series organs with the square scanner unit mounted behind the motor.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
HBELT-SQH-Series Vibrato Scanner Drive Belt - Square ScannerStocked0.1$1.50$1.50

T-Series Vibrato Scanner Drive Belt
Replaces missing, stretched, cracked or broken drive belts in T series organs. This belt slips over the motor pulley and the pulley on the vibrato scanner.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
T-BELTT-Series Vibrato Scanner Drive BeltStocked0.1$1.75$1.75

Internal AC Line Cord
Replacement AC line cable used internally on Hammond C, D, G, BV, CV, RT, B-2, C-2, RT-2, B-3, C-3, RT-3 organs to connect the outlet box plug to the organ's AC distribution panel. The original wire insulation has a tendency to dry rot and flake off leaving bare wires exposed which can contact the organ's metal parts. This is a hazardous situation that can result in mild to severe shocks to the player. This wire is also used on pedal lamps, pedal solo units and for Leslie chorale/tremolo switch wiring. Check your organ's wiring! Six foot length.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
INTACCRDInternal AC Line CordStocked0.5$4.00$4.00

Console Linkage Rod Repair Kit
Having trouble keeping your expression connected to the L-shaped linkage rod? If there is a split where it joins the expression pedal you need this kit. Fits B-2/B-3, C-2/C-3 and RT-2/RT-3 organs. Installs easily with an Allen wrench.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
LINK-KITConsole Linkage Rod Repair KitStocked0.3$46.00$46.00

Run Motor Coupling Spring - Pair
Reproduction of the Hammond run motor coupling spring p/n PO-2345-0 used on all Hammond two motor generators. Couples the run motor flywheel to the generator flywheel.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
RMC-SPRGRun Motor Coupling Spring - PairStocked0.1$10.00$10.00

Felt Cover for Hammond Tone Generator
Reproduction of the green felt cover used on Hammond console tone generators. Fits B-3/C-3/A-100/D-100/RT-3 organs, and later model B-2/C-2/RT-2 organs with narrow tone generator.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
GENCVRFelt Cover for Hammond Tone GeneratorStocked1.0$16.00$16.00

Flipper Tab for L- and M-series Organs
Experienced "tombstone" flipper tabs for L-100 and M-100 series organs. Please specify which tab you would like in the order form comment box. Tabs in picture are for reference only.
ItemDescriptionStatusShip WeightList PriceYour PriceQuantityGurney
SPINET-TABSFlipper Tab for L- and M-series OrgansStocked0.1$5.00$5.00

Now viewing: 1 - 10 of 10 items

Featured Items...